C60 steel – quick summary
C60 is a(n)
french steel
defined in NFA37401/2-99 standard.
(Looking for this designation of material quality, but standard does not match? Click here!)
Basic information
Chemical composition (C60)
Use Case Information
Material groups (C60)
Exact matches for C60 in ASTMA672-96 standard
- Quenched and tempered steels
- Spring steel
- Technical delivery conditions for non alloy steels
- Fully killed steel
- Non-rimming steel
- FF
- Wrought steels
- Cold-rolled strip for springs
- Cold-rolled, quenched and tempered or spring steel strip
- Schedules for wrought steels
- Carbon steel
- Unalloyed steel
- Quenched and tempered seamless circular steel tube
- Quality steel
- QS
- Bright unalloyed steel
- Bright steel products
- Steels for general engineering purposes
- Open die steel forgings for general engineering purposes
- Non-alloy quality and special steels
- Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures
- C-Mn-Si steel
- Fine grained steel
- EN1503/2-2000
- Valves. Materials for bodies, bonnets and covers. Part 1: Steels other than those specified in European Standards
- Heat-treatable steels, alloy steels and free-cutting steels. Non-alloy steels for quenching and tempering
Matches for C60 in any standard defining this steel grade
Usual delivery conditions/forms (C60)
Exact matches for C60 in ASTMA672-96 standard
Matches for C60 in any standard defining this steel grade
Typical applications (C60)
Exact matches for C60 in ASTMA672-96 standard
- Axle
- Shaft
- Spindle
- Hot-saw
- Bolt
- Hot work blanking tool
- Nail set
- Centralizer and jaw, vice grip
- Die [untreated]
- Swage [untreated]
- Coke crusher
- Cross chisel
- Cross-peen hammer
- Bending tool, large
- Pick
- Carpenter's hatchet
- Carpenter's square
- Shovel
- Spade
- Axe
- Bill
- Hatchet
- Collet
- Jaw
- Cramp
- Clamp cheek
- Wrapper knife
- Shoemaker's hammer
- Wood drill, medium-power
- Wood drill
- Adz
- Wedge
- Spud
- Lathe centre
- Prismatic key
- Key
- Household scissors
- Cutting-out scissors
- Round steel bar, hot rolled
- Square bar
- Square
- Hexagon
- Flat steel
- Band steel
- Heavy plate
- Billet
- Strip, cold-rolled [C]
- Pivot
- Axle[pin]
- Draw-in roll
- Blade tip
- Steel bar
- Wire rod
- Wide flats
- Wide strip
- Universal mill plate
- Sheet
- Thin sheet
- Strip
- Open die forging
- Closed die forging
- Stamping
- Details [mech. engineering]
- Spring
- Structural components for heavy demands
- Plate
- Section steel
- Shaped section
- Forging
- Forged piece
- Tubes for machine purposes
- Apparatuses
- Vehicle parts
- Pressure vessel
- Pipeline
- Cold drawn, turned, ground bright bar
- Forged bar
Matches for C60 in any standard defining this steel grade
Mechanical properties (C60) - available in several states, such as
Exact matches for C60 in ASTMA672-96 standard
- quenched and tempered
- normalized
- soft annealed
- A
- quenched and tempered [flat product]
- treated to shearing
- cold rolled and soft annealed
- cold rolled and quenched and tempered
- quenched
- rolled, hard
- hot rolled
- annealed
- annealed, in protective atmosphere
- as rolled and turned
- cold drawn
- cold drawn flat product
- normalized and tempered
- as rolled and turned (+SH)
- cold drawn (+C)
- cold drawn (+C) flat product
- normalized (+N)
- quenched and tempered (+QT)
- treated for cold shearing (+S)
Matches for C60 in any standard defining this steel grade
Heat treatment information (C60) – available instructions for many scenarios, such as
Exact matches for C60 in ASTMA672-96 standard
- normalizing - (min. 1/2 h)
- quenching - oil
- quenching - synthetic
- quenching - water
- tempering - (min. 1 h)
- tempering - air
- tempering - quiet air
Matches for C60 in any standard defining this steel grade
About our service
EQUIMETALS can provide exact chemical composition, mechanical properties in several states, heat treatment procedures for various purposes, as well as detailed corrosion information for over 70 corrosive mediums in several combinations of concentration and temperature.
EQUIMETALS can also offer you close equivalent and similar steels from different countries, and provide you a list of the most typical use case scenarios.
Should you need the information of suitable welding materials, EQUIMETALS can offer you different fillers from several manufacturers. And we have many more information for you!
Get interested? Try out for free!
« Back...